深圳市琦捷电子有限公司(以下简称QJ) 通过ISO9001质量管理体系认证。

深圳市琦捷电子有限公司还有其他规格的电池座，贴片电池座,详情请联系如配有CR2032、CR2450、CR2477、CR2430、CR1220等等,CR2032电池座有多种规格可供客户选择,生产厂家价格

深圳市琦捷电子有限公司的纽扣电池座提供了出色的解决方案,可节省拥挤的...其它 CR2032电池座解决方案通常要高出PCB 表面近.LCP 底座能够完全承受高温回流焊工艺CR2032贴片电池座也具有足够的强度和柔韧性，更换多次都不会引起问题。

6. List the precautions （注意事项列表）

(1)Main body （机身）

Specify the loading direction of battery on battery chamber.

（在电池室内明确说明电池的加载方向）

(2)Manual （指南）

List the precautions how to handle batteries.（列出如何操作电池的预防措施）

7. Do not solder the battery directly. Excessive heating may cause deformation of the battery components such as the gasket, which may lead to the battery swelling, leakage, explosion or ignition.（切勿直接焊接电池。过热会造成电池构件变形，例如密封胶圈的变形可能导致电池膨胀，漏液，爆炸或着火）

8. Observe the soldering condition for the tabbed battery to be specified by the manufacturer. Choose the tabbed battery if soldering is required.

Excessive heating may cause deformation of the gasket, leakage or performance deterioration of the battery.    Assure not to exceed the battery temperature higher than 60℃ at soldering.  

  （遵循制造商指定的标签电池的焊接条件。如果需要焊接，请选择标签电池。

 过热会造成密封胶圈变形，漏液或电池性能退化。确保焊接时电池温度不超过60℃）

9. Use nickel-plated iron or stainless steel for the terminals that contact the battery.

        （使用镀镍的铁或不锈钢作为连接电池的接线端材料）

10. Make sure that terminal contact pressure is 100g minimum for stable contact.

         （确保在持续接触时，接线端触点压力最低限度为100g）

11. Keep the battery contact terminal surfaces clean and free from moisture and foreign matter.

    （保持电池接触端点表面洁净，没有水分和杂质）

12. Before inserting the battery, check the battery contact terminals to make sure they are normal, not bent or damaged. Bent terminals may not make good contact with the battery or may cause it to short-circuit.（在嵌入电池前，检查电池接触端点确保他们是正常的，没有弯曲或损害。弯曲的接线端可能导致无法良好地连接电池或引起短路）

13. Do not overdischarge the battery lower than 0V. It may lead to reversed polarity and cause ignition, heating, leakage or explosion.

    （电池切勿过放电至低于0V。它可能导致反极性，引起着火，变热，漏液或爆炸）

14. Lithium Manganese Dioxide Battery that is almost exhausted still maintains high output voltage that is almost the same as that of a fresh battery. Avoid using a mixture of old and new batteries; replace all batteries in a set with new ones.（锂-二氧化锰电池耗尽时仍可保持高的输出电压，几乎与新的电池无异。避免新旧电池混用，请整套更换新电池）

15. Lithium Manganese Dioxide Battery requires considerable time to regain their normal voltage after even a slight short-circuit. Therefore, should the battery be short-circuited, wait an adequate time for the battery to recover before measuring its electrical characteristics.

       （锂-二氧化锰电池需要相当长的时间恢复到它们的正常电压即便是轻微短路。因此，

           短路的电池在测量其电性能前，需要足够的时间恢复）

16. Use a high impedance (1MΩ or higher) voltmeter to measure battery voltage.

        （使用高阻抗 (1MΩ or 以上) 电压表测量电池电压）

17. Battery characteristics vary with type and grade, even when batteries are the same size and shape. When replacing batteries with new ones, be sure to carefully check the symbols and numbers on each battery.（电池特性随型号和级别而变化，即便是同样大小和形状。在更换新电池时，务必仔细检查每个电池上的符号和数字）